Lint, dust, and other types of dirt accumulate over time on your smartphone speakers, which you probably aren't aware of. You'll notice your sound becomes muffled if you don't clean them soon enough. Additionally, this may occur if you unintentionally spill water on your phone. So if you are wondering how to clean a phone speaker, here are the solutions.There are a few fantastic do-it-yourself methods for cleaning the speakers from both the exterior and inside of the phone before visiting the repair shop. Here's how to clean a phone speaker that has been contaminated by water, grime, or dust.
Here are some of the factors you need to take note of while you are looking into how to clean mobile speaker:
Use a cotton swab, compressed air, or a toothbrush to clean the speaker on your phone.
Make sure you are comfortable taking apart your phone before attempting to clean the speakers from the inside.
Use a desiccant to dry out your speakers, or play a certain tone to stimulate sound waves.
Step 1: Look for the phone's speakers. The first thing you need to figure out while looking into how to clean the speaker of a phone is that the speakers are at the bottom of an iPhone, to the right and left of the charger port. In addition to being on the bottom, Samsung speakers are often only located to the left or right of the charger port.
The base of the phone's front face, where you put your ear, is usually always where you'll find the ear speakers.
Step 2: Use a cotton swab to rub the outsides of your phone speaker. Apply some pressure as you move a cotton swab lightly in a circular manner over your speaker holes. Continue doing this until all of the dirt has been removed. Press the cotton swab into the speaker holes if they are large enough. But only enough pressure should be applied so that the cotton swab, just at tip, fits into the slot. Once within, apply a little pressure and rub the cotton swab left to right.
Step 3: Make a tiny ball out of sticky tack and place it over the speaker openings. Squeeze a piece of sticky tack that is 1 inch (2.5 cm) long into a ball. Compress it continuously until it becomes flexible and soft. Then, firmly press it into the speaker holes. Put enough force on the adhesive tack so that it enters the speaker. Remove it after holding it in place for two to three seconds; dirt should be adhered to the sticky tack. Repeat this procedure until no more dirt is seen coming from the speakers.
Step 4: Small speaker grills should be cleaned with a medium-bristle toothbrush. Place the brush with the top or bottom of your phone in mind. Move it up and down while keeping it aligned to the top of your phone. After that, clean by sliding your toothbrush left and right while holding it parallel to the surface of your phone.
Step 1: Get yourself a can of compressed air. Electronics retailers, office supply stores, and online providers all carry compressed air cans. Try it out by squeezing the nozzle down while pointing it downward. Get a sense of how much air each spray emits.
Step 2: To increase precision, attach the straw to the can's nozzle. Attach a tiny straw to the compressed air can nozzle using the screwdriver. Try it out by squeezing the nozzle down while pointing it downward. The straw's tip needs to be where the air is to be released.
Step 3: In three to four brief bursts, blow compressed air into the speaker slot. Maintain a distance of at least 12 inch (1.3 cm) between the straw's nozzle or tip and the speaker aperture. This will get rid of extra dirt from your cotton swab that was squeezed into the speaker.
Step 1: Your phone's back lid can be removed using a spudger and suction cup. Wondering how to clean my phone speaker from the insides? Use a hairdryer on low heat for around 15 seconds to warm the phone's edge. Apply a suction cup to the rear after that. Pull the suction lever slowly in your direction while the screen is facing downward. Put a spudger's flat end between the perimeter aperture and lever that towards you at the same time. Lever the back piece until it pops off by continuing to tug on the suction cup.
Step 2: Take off the metal covers that are covering the speakers. Usually, metal covers keep the phone's speakers and earphones in place. By using a screwdriver, get rid of the screws keeping the covers on. Next, gently remove the speakers.
Step 3: Use a microfiber cloth soaked in rubbing alcohol to clean the speakers. Rub some rubbing alcohol in a thin layer onto a soft microfiber. Cleanse the speaker components by gently scrubbing them. Blow softly into the apertures from the outside. After that, carefully rub the speaker apertures with a cotton swab that has been dipped in alcohol.
Step 4: If you are still unable to access your speakers, detach the second back piece. To access the speaker apertures on some phones, usually Samsung brands, you must remove a second rear piece. Although the precise number differs by model and manufacturer, there will be an additional 10 to 13 screws to remove from these phones. Each screw should be turned anticlockwise with a 4 inch screwdriver until it comes loose. Pull the second back piece off after that.
Step 1: Switch your phone off. In case you have spilt water on your phone, you should first switch off your phone before attempting to know how to clean my phone speaker. Turning off your gadget as soon as you can is necessary.
Step 2: Use a towel to dry the phone. The phone should be secure to handle as long as it is off. Make sure to properly dry the outside.
Step 3: Put silica gel packs in a sealed plastic bag with the phone inside. You can buy silica gel packs online or discover some in packaging lying about your home. These little white packs typically have the phrase "Do not eat" printed on them.
Step 4: Give the phone at least a day in the bag. The greatest location is one that receives some sunlight because it will aid in removing the moisture from the phone.
Step 5: Switch your phone on. You can turn on your phone after checking for any traces of water.
Step 1: Make sure your device has been fully dried. If you respond immediately and use a desiccant, you can rescue a wet phone.
Step 2: Launch your mobile browser and play the tone video. It might launch immediately on the YouTube app if you have one.
There are many tones available that are marketed for draining water from your speakers. You may use the search box to discover a different video that is comparable if this tone is incompatible with your device.
Step 3: Play the video. Make sure the volume on your device is at its highest setting. This will guarantee that the tones are played correctly and provide the sound waves required to force the water out.
Step 4: If necessary, repeat. During playback, you might need to reposition the device. To guarantee that water exits your device, keep the holes of the speakers facing down at all times.
You can use silica gel to clean a clogged phone speaker.
You can use several methods to clean your speakers, including cotton swabs, silica gel, and compressed air.
Apply rubbing alcohol to a microfiber towel and wipe the speakers down. A microfiber cloth should be dipped in a little amount of rubbing alcohol. The speaker parts should be cleaned with gentle scrubbing. Blow softly from the outside into the apertures.
Have you been wondering how to remove dust from a phone speaker, and considering using sanitizer? Note that using hand sanitizer on a mobile device, the display, speaker, camera, and microphone is not advisable. This could lead to the glue on the display being removed, which could harm the display. Using sanitizer on the phone's microphone and speaker could have an adverse effect on the audio system.